Tapered Buff 1.5" Diameter

Tapered Buff 1.5" Diameter

1.5" Tapered buff made of unbleached muslin. Hand made and premium quality. Generally used with buffing compositions to polishing inside surfaces of hollow ware or tubes. Can also be set-up with glue and abrasive grain or used with greaseless compound and wheel grease for fast and/or heavy cut down operations. Construction produces a very firm buff with little give under pressure. Will need to be raked occasionally when used with buffing compounds. Designed for use on a cone point mandrel or tapered spindle.

$18.00 Each

This item is out of stock and cannot be purchased at this time, please check back again later.

Cylinder Buff
Tapered and Cylinder Buffs

Additional Information

SKU B202650
Average Weight 0.05 lbs.
Outside Diameter 1-1/2"
Primary Material Cotton, Muslin
Cloth Density 48/48
Max Face Width 1-1/2"
Center Hole 1/4"
Center Reinforcement Shellac
Treatment Untreated
Purpose Cut or Color Buffing
Max RPM 10,000
Minimum Order 1
Availabilty Stock Item
Case Quantity 10
Non-Defect Return With RMA - See Policy
Ships From MT, NY
Ships Via UPS, USPS, FedEx
Warranty Yes
Product Type Cylinder Buff
Additional Info Requires the use of a cone point mandrel or tapered spindle for proper mounting and safe operation.

Description: Tapered Buff

About: This buff is constructed in the shape of a cone, it is a firm buff and generally used to buff and polish inside diameters where there is no bottom to be polished. The tapered and cylinder buffs are exactly the same except as to shape. The cylinder buff has parallel sides and the tapered buff tapers to a rounded point. Designed for use on a taper spindle.

Typical Application: For buffing the inside surfaces of any hollow ware or tubes, where there is no bottom to be polished. Tripoli, rouge, or other compositions may be used. They also may be set up with glue and abrasive grain or used with greaseless compound and wheel grease in heavy cut down operations.

Construction: Suitable grades of unbleached muslin are used. These buffs are made up from full discs of the required diameter die cut from the proper material. The discs are then counted and turned to the desired ply. The sections are sewed with concentric sewing and then hand sewed together. The buffs are raked for increased uniformity and a shorter break-in time. The arbor hole is hardened with shellac to help prevent over stretching.

Sizes: 1-1/2", 2", 2-1/2", 3", and 3-1/2" diameter. The length is approximately the same as the diameter.

Precautions: Wear appropriate safety clothing, respiratory, and eye protection during use. Requires the use of a cone point mandrel or tapered spindle for proper mounting and safe operation.

Note: Industrial grade. Guaranteed for quality and performance.

All related media files will be listed here when available.

Product Questions

I would like to order some tapered buffs but I'm not sure what mandrel to use.

Hello Gary,

You can use either of the following for chuck mount application (drill, die grinder, etc.):

https://www.infinish.com/index.php/more-products/mandrels/e192570.html or https://www.infinish.com/index.php/more-products/mandrels/e192577.html

And for use on a bench grinder or pedestal buffer with a 1/2" or 5/8" arbor shaft select a left or right hand taper spindle:

https://www.infinish.com/index.php/more-products/mandrels/e192578.html or https://www.infinish.com/index.php/more-products/mandrels/e192579.html

https://www.infinish.com/index.php/more-products/mandrels/e192573.html or https://www.infinish.com/index.php/more-products/mandrels/e192574.html

Hope this helps.

Rate the answer?
0 Review(s)